FIC 2150cc injectors can be used with all Gen 3 Hemi engines including the 6.2L supercharged Hellcat, TRX and Trackhawk models. Includes a set of 8 injectors with solder-in pigtails or add Plug & Play adaptors.
Vehicle Fitment:
6.4L Hemi V8 (Apache 392)
6.2L Hemi V8 (Hellcat Demon Redeye Supercharged)
6.1L Hemi V8 (SRT8)
5.7L Hemi V8 (Eagle)
• 2021-2023 Dodge Ram TRX (6.2)
• 2009-2023 Dodge Charger (5.7 6.1 6.2 6.4)
• 2009-2023 Dodge Challenger (5.7 6.1 6.2 6.4)
• 2018-2021 Jeep Grand Cherokee Trackhawk (6.2)
• 2014-2021 Jeep Grand Cherokee SRT (6.4)
• 2006-2013 Jeep Grand Cherokee SRT8 (5.7 6.1 6.4)
Install Adapter Options:
• Solder-In Pigtails PGTDEN8
• Plug & Play Harness PADPDtoU8
DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS.
More from FIC:
Fuel Injector Clinic Injector Set: 8x2150cc/min (200lbs/hr) at 3 bar (43.5psi) fuel pressure and 240lbs/hr (2500cc/min) at OE 58psi (4 bar) fuel pressure. Saturated / High Impedance Injectors. Includes pigtails PGTDEN8 or add Plug & Play adaptors PADPDtoU8.
These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS. Plug and Play Dodge ECU Data available at fuelinjectorclinic.com.
This massive high performance injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90 degrees F fuel temperature using CF-16B calibration fluid.
CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This injector set is precisely matched using Fuel Injector Clinic’s proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid.
Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.
This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
| Select Install: | With Pigtails PGTDEN8, With P&P Adapters PADPDtoU8 |
|---|
Fast Shipping with Professional Packaging
We provide a variety of shipping options thanks to our long-standing relationships with UPS, FedEx and DHL. Our warehouse personnel are well trained and will be able to pack your goods in accordance with the exact and precise specifications. Before shipping, all goods are carefully examined and secured. We deliver to thousands of clients each day across multiple countries. The fact that we're dedicated to becoming the largest online retailer in the world is obvious. Warehouses and distribution centers can be found in Europe as well as the USA.
Orders that contain more than one item are assigned processing times according to each item.
We will inspect each and every one of the items ordered before shipping. The majority of orders are shipped within 48-hours. Delivery is expected to take between 3 and seven days.
Returns
We do not manage the stock in our warehouse or factory. The levels of stock can change at any time. Please be aware that it's possible for your order to be out of stock after you have placed the order.
The policy is 30 days. If it's been longer than 30 days since you bought the item We're sorry to say that we can't offer you a full refund or exchange.
The item cannot be used, and it must be in its original condition. It must also still be in the original package.
Related products
Electrical Tape
